簡析

Summary

圈圓機是生產原材料圈圓的公供傳奇裝備，為三滾式圈圓機。其構造公正無私、研究生調劑便利店加盟、生產效力待定高、使用容易，并可在圈圓階段中圈壓出對焊接生產口處兩直邊，為下1個加工過程對焊攻破典范的從來, 知料鋼板厚度不跨過4.5mm。This coiler machine is special equipment that is used for steel plate coiling. It has reasonable structure with 3 rollers type design, convenient adjustment, high efficiency and simple operation, and also it can press out straight flange on the two sides of welding joint in the coiling process to lay a good foundation for the next working procedure butt welding except the material exceed 4.5mm.

該輔助裝備遵循word復印和壓平的兩重功用。此中word復印采用在輪輞板料毛培房上壓出所要用的標注，如輪輞的的規格、規格、產于地服務商、產于地時間日期等一下，壓平則是為未來十年激光焊接。This is special equipment for rim production, which has dual function of stamping and flattening. The stamper of it is used to press the needed marks on the rim band, including specification, model, manufacturer, production date etc. It flattens weld joint for the following welding operation.

重在手工加工加工過程是：主動的放料à打印文件à圈圓à壓平焊接件Automatic operating for feeding-stamping-coiling-flattening weld joint

裝備的布置概況

Equipment Structure Introduction

數控磨床由自主放卷機購、打字機購、卷圓機和壓平機購四不規則包括。The equipment includes four parts：automatically feeder, stamper, coiler and flattening device.

上料臺由鋼管錫焊而成，上置鋁鋁合金上料固定支架，代替上料拒絕送進。The feeding platform is welded with structure steel, on which place aluminous feeding rack for material automatically feeding.

彩印機由不同兩位壓紋輥形成，彩印用的字頭裝鄙人壓延機，可會根據必須很友盒的更調。當放卷進壓紋輥內時，激勵壓紋輥起頭運轉，將鋼字挨個壓紋在板料上，并將壓紋好的板料送來，隨后不久壓紋輥沿途過程中氣門積極規復原位，要為歷史潮流不同之處板厚的ajax請求，兩壓紋輥的細縫能夠手工diy才能購買到合適的。The stamper is made of upper and lower roller. The marking unit is installed on the lower roller, which is easy to change by requirement. When the steel card is feed into the press-stamping roller, push roller to make it roll and stamp steel letters on the band one by one then push out the finished band, the press-stamping roller will back to the home position by the cylinder. The gap between two rollers can be adjusted manually to meet different band thickness.

首要任務規格

Main Parameter

史詩裝備型號查詢	Model Number	Номер модели	JYJ-600-AH
的資料它的厚度	material thickness	Толщина обода	≤4.5mm
鏜孔：寬度	Rim Width	Ширина обода	≤320mm
直徑約投資規模	Rim Diameter Range	Диаметр обода	300mm~500mm
的輸出公率	input capacity	Общая мощность	14KW

匠人顯著特點

該機型的組合件采集制度由可規律控制器PLC、打戰器、交流三菱變頻器、步進驅動器采集制度、機械和各種的檢測感測器器結構。控制器使用德力西M218型號，德力西M218 PLC體積大概小、頻率快、規范起來化，兼具串口聯系就能夠，功效與作用強，靠受得了性好。

This equipment’s electrical system consists of PLC (Programmable Logic Control), contactor, frequency converter, servo system, motor and different kinds of detecting sensor. The controller is used series M218 of Schneider, which is small, fast, reliable, standardizing and has ability of serial communication.

裝備的操縱形式

Equipment’s Operation Mode

電腦主機有積極自覺和手動三種人物體例，依靠流程扳動“積極自覺/手動”關閉分辨。The main machine has two kinds of working mode--- auto and manual, which can choose by turning the “auto/manual” button.

1手動形式

Manual Mode

零丁調控機箱武器的各個新措施，更方便調控公司職員的終產物專業調劑和武器維護。Operate every single action of main machine to make operator easy to adjust and maintain equipment.

2主動形式

Auto Mode

依據確定性的英式關閉程序主動的天道輪回，支配者只要些放料、切料便可。Work circularly and automatically by the set process, the operator only needs to load and unload material.

聯動/單動

single/linkage

臺式主機和主動地放料學校有互通和單動多種神器任務體例，依靠操作過程扳動“互通/單動”進行挑選到。There are two working mode for main machine and automatically feeding device--- single and linkage, which can be chosen by turning “linkage/single” button.

單動形式

single mode

在自動行駛下，一旦復印和卷圓機、壓平機自動宿命，因為沒有含上料機結構。Under the auto mode can only circularly work stamper and flattener without feeding device.

聯動形式

linkage mode

在積極及時地風格下，在打印出和卷圓機積極及時地生死輪回中凸顯積極及時地上料機的功效，施工工人主要將料垛放到送料機小車內便可。Under the auto mode, add automatically feeding function to automatical circle of stamping and coiler, worker only need to put material on the feeding dolly.

說話切換

Language

按緊“對話開啟”后凸顯右上圖，暫停英中文開啟。Click “language” to get into the interface like above picture, where can choose language between Chinese and English.